1. Home
  2. Blog
  3. Building maintenance
Building maintenance

Post Construction Window Cleaning by Drone: What It Handles and What Needs Hand Work

A drone wash clears construction dust and loose film from new glass and cladding, while paint, adhesive and cement splatter still need careful hand detailing.

Post Construction Window Cleaning by Drone: What It Handles and What Needs Hand Work
Short answer

Post construction window cleaning removes the dust and residue left on a building after the trades finish. A drone wash handles loose dust, dried mud, drywall film and general grime across the whole exterior. Bonded material such as paint, adhesive, sealant smears and cement splatter needs hand detailing by a cleaner working at the glass.

Why a new building is never handed over clean

Construction is dirty work, and the exterior is the last thing anyone thinks about until handover is close. By then the glass and cladding have lived through months of cutting, grinding, pouring and painting.

The result is a mix of different kinds of mess. Some of it is loose and some of it is stuck fast. Treating it all the same way is how new glass gets scratched, so it helps to sort the mess into two groups before anyone starts.

What a drone wash can handle

A drone washes the exterior with deionized water and a safe cleaning solution while the pilot stays on the ground. It is well suited to anything that will loosen and rinse away.

  • Airborne dust from cutting concrete, stone and drywall.
  • Dried mud and splash marks on lower floors.
  • The dull film left when dusty rain dries on new glass.
  • Loose grit on sills, ledges, frames and cladding panels.
  • Dust that settled on the roof and upper facade from work on neighboring sites.
  • General grime on a building that sat finished for a while before handover.

What needs hand detailing

Some residue is bonded to the glass. A rinse will not shift it, and more water pressure is not the answer.

Paint overspray and drips, adhesive from protective film and labels, smears of sealant, stickers, and splatter from cement, mortar, stucco and plaster all fall into this group. They need a person at the glass with the right tools and cleaning products, working pane by pane.

Cement based splatter deserves special care. It is hard and gritty. Scraping or rubbing it dry can drag particles across the pane and scratch it. It can also mark the glass chemically if it sits for a long time, so flag it early rather than at the end.

Welding and grinding sparks are another case. They can pit the surface of glass. That is damage, not dirt, and no cleaning method removes it.

Why the two steps work well together

A drone wash and hand detailing are not rivals. They do different jobs, and the order matters.

Washing first takes the loose grit off the glass. That makes detailing safer, because there is less abrasive dust on the pane when a cleaner starts working on a stuck spot. It also shows clearly what is left. Once the dust film is gone, paint specks and cement spots stand out, and the detail work can be targeted at the panes that need it instead of every pane on the building.

On a tall building this can cut down how much of the facade needs close access at all.

Sequencing the clean with the builder

Timing is where post construction cleans go wrong. Wash too early and the building is dusty again within days. A few questions for the site team help set the date.

  • Is exterior work finished, including sealant, painting and touch ups?
  • Are scaffolding, hoists and exterior protection down?
  • Is landscaping and paving done, or will it throw up more dust?
  • Is the roof clear of trades and materials?
  • Where can the area below be cordoned off, and when is the site quiet?
  • Who will walk the building afterward and sign off?

Inspection and photo records at handover

Clean glass shows everything. Scratches, pits and coating marks that were hidden under dust become visible once the wash is done. It is better to find them before handover than to argue about them after.

Drone Sky Cleaners follows a set process: pre-inspection, flight planning, cordoning off the area below, cleaning, final inspection and before-and-after photos. On a new build, those photos give the owner and the builder a shared record of the condition of the exterior on the day it was cleaned.

The pre-inspection is also the time to agree which marks are expected to wash off and which will be passed to a detail crew.

Limits to plan around

Drone work depends on conditions. Strong wind and bad weather delay flights. Heavy buildup can need a second pass. Sites near airports may need airspace authorization before flying.

In the United States, commercial drone work is flown under FAA Part 107 by a certified remote pilot with a registered drone. In Canada, Transport Canada drone rules apply in a similar way. Rules change, so operators must check the current rules for each site. Build a little slack into the handover program for all of this.

Common questions

Who usually pays for the post construction clean?

It depends on the contract. Sometimes a final clean is part of the builder's scope, and sometimes the owner arranges it separately. Check what the contract says about exterior glass and facade cleaning before handover so nothing falls between the two.

Can protective film be left on the glass until the wash?

Follow the glass or frame supplier's guidance on how long film may stay on. Film left in the sun too long can leave stubborn adhesive behind, which then needs hand work. Tell the cleaning crew what was used and when it came off.

Does a new building need another clean soon after handover?

Often it helps. Tenant fit outs, landscaping and nearby sites keep producing dust for a while. Many owners book a follow up wash once the building is occupied, then move to a regular maintenance schedule.

Contact

Fill the form below to get started

Send the building details and we'll come back with a quote.

(647) 361-5616[email protected]
1001 Finch Ave W, Toronto, ON M3J 2C7

Free quote request

Takes about a minute.

CallGet a Free Quote